[b]Note:[/b] When exporting to Android, make sure to enable the [code]INTERNET[/code] permission in the Android export preset before exporting the project or using one-click deploy. Otherwise, network communication of any kind will be blocked by Android.
Request a disconnection from a peer. An [constant ENetConnection.EVENT_DISCONNECT] will be generated during [method ENetConnection.service] once the disconnection is complete.
Request a disconnection from a peer, but only after all queued outgoing packets are sent. An [constant ENetConnection.EVENT_DISCONNECT] will be generated during [method ENetConnection.service] once the disconnection is complete.
Force an immediate disconnection from a peer. No [constant ENetConnection.EVENT_DISCONNECT] will be generated. The foreign peer is not guaranteed to receive the disconnect notification, and is reset immediately upon return from this function.
Sends a ping request to a peer. ENet automatically pings all connected peers at regular intervals, however, this function may be called to ensure more frequent ping requests.
Sets the [code]ping_interval[/code] in milliseconds at which pings will be sent to a peer. Pings are used both to monitor the liveness of the connection and also to dynamically adjust the throttle during periods of low traffic so that the throttle has reasonable responsiveness during traffic spikes. The default ping interval is [code]500[/code] milliseconds.
Forcefully disconnects a peer. The foreign host represented by the peer is not notified of the disconnection and will timeout on its connection to the local host.
Sets the timeout parameters for a peer. The timeout parameters control how and when a peer will timeout from a failure to acknowledge reliable traffic. Timeout values are expressed in milliseconds.
The [code]timeout_limit[/code] is a factor that, multiplied by a value based on the average round trip time, will determine the timeout limit for a reliable packet. When that limit is reached, the timeout will be doubled, and the peer will be disconnected if that limit has reached [code]timeout_min[/code]. The [code]timeout_max[/code] parameter, on the other hand, defines a fixed timeout for which any packet must be acknowledged or the peer will be dropped.
Unreliable packets are dropped by ENet in response to the varying conditions of the Internet connection to the peer. The throttle represents a probability that an unreliable packet should not be dropped and thus sent by ENet to the peer. By measuring fluctuations in round trip times of reliable packets over the specified [code]interval[/code], ENet will either increase the probability by the amount specified in the [code]acceleration[/code] parameter, or decrease it by the amount specified in the [code]deceleration[/code] parameter (both are ratios to [constant PACKET_THROTTLE_SCALE]).
When the throttle has a value of [constant PACKET_THROTTLE_SCALE], no unreliable packets are dropped by ENet, and so 100% of all unreliable packets will be sent.
Intermediate values for the throttle represent intermediate probabilities between 0% and 100% of unreliable packets being sent. The bandwidth limits of the local and foreign hosts are taken into account to determine a sensible limit for the throttle probability above which it should not raise even in the best of conditions.
The time at which packet loss statistics were last updated (in milliseconds since the connection started). The interval for packet loss statistics updates is 10 seconds, and at least one packet must have been sent since the last statistics update.
The maximum number of unreliable packets that should not be dropped. This value is always greater than or equal to [code]1[/code]. The initial value is equal to [constant PACKET_THROTTLE_SCALE].
Internal value used to increment the packet throttle counter. The value is hardcoded to [code]7[/code] and cannot be changed. You probably want to look at [constant PEER_PACKET_THROTTLE_ACCELERATION] instead.
The time at which throttle statistics were last updated (in milliseconds since the connection started). The interval for throttle statistics updates is [constant PEER_PACKET_THROTTLE_INTERVAL].
The throttle's acceleration factor. Higher values will make ENet adapt to fluctuating network conditions faster, causing unrelaible packets to be sent [i]more[/i] often. The default value is [code]2[/code].
The throttle's deceleration factor. Higher values will make ENet adapt to fluctuating network conditions faster, causing unrelaible packets to be sent [i]less[/i] often. The default value is [code]2[/code].
The interval over which the lowest mean round trip time should be measured for use by the throttle mechanism (in milliseconds). The default value is [code]5000[/code].
