- Back to 1-based layer names to make it clearer in editor UI
- Layer bit accessors are renamed to layer value and 1-based too
- Uniform errors and documentation in render and physics
- Fix a few remaining collision_layer used in place of collision_mask
Infinite inertia:
Not needed anymore, since it's now possible to set one-directional
collision layers in order for characters to ignore rigid bodies, while
rigid bodies still collide with characters.
Ray shapes:
They were introduced as a work around to allow constant speed on slopes,
which is now possible with the new property in CharacterBody instead.
Same thing that was already done in 2D, applies moving platform motion
by using a call to move_and_collide that excludes the platform itself,
instead of making it part of the body motion.
Helps with handling walls and slopes correctly when the character walks
on the moving platform.
Also made some minor adjustments to the 2D version and documentation.
Co-authored-by: fabriceci <fabricecipolla@gmail.com>
When synchronizing CharacterBody motion with moving the platform using
direct body state, only the linear velocity was taken into account.
This change exposes velocity at local point in direct body state and
uses it in move_and_slide to get the proper velocity that includes
rotations.
* Added a new macro SNAME() that constructs and caches a local stringname.
* Subsequent usages use the cached version.
* Since these use a global static variable, a second refcounter of static usages need to be kept for cleanup time.
* Replaced all theme usages by this new macro.
* Replace all signal emission usages by this new macro.
* Replace all call_deferred usages by this new macro.
This is part of ongoing work to optimize GUI and the editor.
Now static body is used for moving platforms through kinematic motion
property, so sync to physics needs to be in StaticBody2D instead of
CharacterBody2D.
Constant kinematic motion is also supported in combination with sync to
physics for smoother movements.
Fixing by applying the movement in two steps, first the platform
movement, and then the body movement. Plus, add the platform movement
when we are on_wall.
* there is now a more clear distinction between camera_2d and camera_3d functions in the engine code
* simplified camera2d's exported interface - now everything happens directly with the 'current' variable and make_current and clear_current are no longer exposed- there were some situations where calling one instead of set_current would result in incomplete results
* rebased to current godot master
More accurate unsafe motion calculation
* Safe and unsafe motion are calculated by dichotomy with a limited
number of steps. It's good for performance, but on long motions that
either collide near the beginning or near the end, the result can be
very imprecise.
* Now a factor 0.25 or 0.75 is used to converge faster when this case
happens, which allows longer motions to get more accurate collision
detection.
* Makes snap collision more precise, and helps with cases where diagonal collision on the border of a platform can lead to the character being stuck.
Additional improvements to move_and_slide:
* Handle slide canceling in move_and_collide with 0 velocity instead of
not applying it.
* Better handling of snap with custom logic to cancel sliding.
* Remove small jittering when using stop on slope, by canceling the
motion completely when the resulting motion is less than margin instead
of always projecting to the up direction (in both body motion and snap).
Co-authored-by: fabriceci <fabricecipolla@gmail.com>
New property disable_mode to set different behaviors:
Remove: remove from physics simulation
MakeStatic: change body mode to static (doesn't affect area and soft body)
KeepActive: do nothing
Extra change:
Handle disable/enable node state with specific notifications, in order
to differentiate global pause from disabled nodes.
* Functions to convert to/from degrees are all gone. Conversion is done by the editor.
* Use PROPERTY_HINT_ANGLE instead of PROPERTY_HINT_RANGE to edit radian angles in degrees.
* Added possibility to add suffixes to range properties, use "min,max[,step][,suffix:<something>]" example "0,100,1,suffix:m"
* In general, can add suffixes for EditorSpinSlider
Not covered by this PR, will have to be addressed by future ones:
* Ability to switch radians/degrees in the inspector for angle properties (if actually wanted).
* Animations previously made will most likely break, need to add a way to make old ones compatible.
* Only added a "px" suffix to 2D position and a "m" one to 3D position, someone needs to go through the rest of the engine and add all remaining suffixes.
* Likely also need to track down usage of EditorSpinSlider outside properties to add suffixes to it too.
Make sure the direction of the motion is preserved, unless the depth is
higher than the margin, which means the body needs depenetration in any
direction.
Also changed move_and_slide to avoid sliding on the first motion, in
order to avoid issues with unstable position on ground when jumping.
Co-authored-by: fabriceci <fabricecipolla@gmail.com>
