Now static body is used for moving platforms through kinematic motion
property, so sync to physics needs to be in StaticBody2D instead of
CharacterBody2D.
Constant kinematic motion is also supported in combination with sync to
physics for smoother movements.
Fixing by applying the movement in two steps, first the platform
movement, and then the body movement. Plus, add the platform movement
when we are on_wall.
More accurate unsafe motion calculation
* Safe and unsafe motion are calculated by dichotomy with a limited
number of steps. It's good for performance, but on long motions that
either collide near the beginning or near the end, the result can be
very imprecise.
* Now a factor 0.25 or 0.75 is used to converge faster when this case
happens, which allows longer motions to get more accurate collision
detection.
* Makes snap collision more precise, and helps with cases where diagonal collision on the border of a platform can lead to the character being stuck.
Additional improvements to move_and_slide:
* Handle slide canceling in move_and_collide with 0 velocity instead of
not applying it.
* Better handling of snap with custom logic to cancel sliding.
* Remove small jittering when using stop on slope, by canceling the
motion completely when the resulting motion is less than margin instead
of always projecting to the up direction (in both body motion and snap).
Co-authored-by: fabriceci <fabricecipolla@gmail.com>
New property disable_mode to set different behaviors:
Remove: remove from physics simulation
MakeStatic: change body mode to static (doesn't affect area and soft body)
KeepActive: do nothing
Extra change:
Handle disable/enable node state with specific notifications, in order
to differentiate global pause from disabled nodes.
* Functions to convert to/from degrees are all gone. Conversion is done by the editor.
* Use PROPERTY_HINT_ANGLE instead of PROPERTY_HINT_RANGE to edit radian angles in degrees.
* Added possibility to add suffixes to range properties, use "min,max[,step][,suffix:<something>]" example "0,100,1,suffix:m"
* In general, can add suffixes for EditorSpinSlider
Not covered by this PR, will have to be addressed by future ones:
* Ability to switch radians/degrees in the inspector for angle properties (if actually wanted).
* Animations previously made will most likely break, need to add a way to make old ones compatible.
* Only added a "px" suffix to 2D position and a "m" one to 3D position, someone needs to go through the rest of the engine and add all remaining suffixes.
* Likely also need to track down usage of EditorSpinSlider outside properties to add suffixes to it too.
Make sure the direction of the motion is preserved, unless the depth is
higher than the margin, which means the body needs depenetration in any
direction.
Also changed move_and_slide to avoid sliding on the first motion, in
order to avoid issues with unstable position on ground when jumping.
Co-authored-by: fabriceci <fabricecipolla@gmail.com>
CharacterBody has a linear_velocity property to replace the argument in
move_and_slide.
StaticBody handles reporting linear/angular velocity correctly when
kinematic motion is used (in 3D, used in vehicle and navigation).
Safe margin property on CharacterBody only, used as argument in
move_and_collide.
Removed kinematic_safe_margin in 3D physics server, not really useful
and now harmonized with 2D.
Does the same thing as simulate motion from RigidBody in Kinematic mode,
and CharacterBody (previously KinematicBody).
Added support for constant linear/angular velocity with kinematic_motion
in StaticBody, which moves the body in physics.
Updated documentation for StaticBody and CharacterBody to describe their
functionalities more accurately.
MODE_DYNAMIC instead of MODE_RIGID
MODE_DYNAMIC_LOCKED instead of MODE_CHARACTER
No more special case for sleeping behavior for MODE_DYNAMIC_LOCKED
(MODE_CHARACTER was forcing the body not to sleep, which is redundant
with can_sleep and wasn't done in Bullet).
- snap property to replace move_and_slide_with_snap()
- floor_max_angle, stop_on_slope, infinite_inertia, max_slides,
up_direction properties to replace arguments from move_and_slide()
- up direction now defaults to Vector3.UP and Vector2.UP
PhysicsBody now has methods move_and_collide/test_move and needed
properties for these methods: safe margin, locked axes (3D only).
Moved collision_exceptions from StaticBody to PhysicsBody for 3D
(same as 2D, and conforms to documentation).
RigidBody doesn't have test_motion method anymore, it's now redundant
with PhysicsBody.test_move.
Happy new year to the wonderful Godot community!
2020 has been a tough year for most of us personally, but a good year for
Godot development nonetheless with a huge amount of work done towards Godot
4.0 and great improvements backported to the long-lived 3.2 branch.
We've had close to 400 contributors to engine code this year, authoring near
7,000 commit! (And that's only for the `master` branch and for the engine code,
there's a lot more when counting docs, demos and other first-party repos.)
Here's to a great year 2021 for all Godot users 🎆
I couldn't find a tool that enforces it, so I went the manual route:
```
find -name "thirdparty" -prune \
-o -name "*.cpp" -o -name "*.h" -o -name "*.m" -o -name "*.mm" \
-o -name "*.glsl" > files
perl -0777 -pi -e 's/\n}\n([^#])/\n}\n\n\1/g' $(cat files)
misc/scripts/fix_style.sh -c
```
This adds a newline after all `}` on the first column, unless they
are followed by `#` (typically `#endif`). This leads to having lots
of places with two lines between function/class definitions, but
clang-format then fixes it as we enforce max one line of separation.
This doesn't fix potential occurrences of function definitions which
are indented (e.g. for a helper class defined in a .cpp), but it's
better than nothing. Also can't be made to run easily on CI/hooks so
we'll have to be careful with new code.
Part of #33027.
Which means that reduz' beloved style which we all became used to
will now be changed automatically to remove the first empty line.
This makes us lean closer to 1TBS (the one true brace style) instead
of hybridating it with some Allman-inspired spacing.
There's still the case of braces around single-statement blocks that
needs to be addressed (but clang-format can't help with that, but
clang-tidy may if we agree about it).
Part of #33027.
Part of #33027, also discussed in #29848.
Enforcing the use of brackets even on single line statements would be
preferred, but `clang-format` doesn't have this functionality yet.
