"less" should be used for quantity, rather than "lesser".
Existing scripts that use `or_lesser` in `_get_property_list()`
will need to be updated to account for this change.
Values lower than 1.0 can be used to make the fog rendering not fully
obstruct the sky. This can be desired when using fog as a purely
atmospheric effect, without intending to use fog for open world fog
fading.
When set to 0.0, fog rendering behavior will be similar to Godot 3.x
where sky rendering was never affected by fog.
This allows light sources to be specified in physical light units in addition to the regular energy multiplier. In order to avoid loss of precision at high values, brightness values are premultiplied by an exposure normalization value.
In support of Physical Light Units this PR also renames CameraEffects to CameraAttributes.
- Add `positive_only` property hint to disallow using negative presets.
These values are clamped in several places in the editor already,
so this avoids displaying presets that don't work.
- Move the Zero preset at the end of the positive list to match
the custom property editor. It's also used less often than Linear,
Ease In and Ease Out.
- Rename presets to be consistent between the easing property editor
and custom property editor.
- Remove unused `inout` hint which was redundant since it was already
the default.
The value is already clamped in the editor, but it wasn't being
clamped when the value was set via code. Values outside the [0.0; 1.0]
range can result in broken rendering.
- Enable Read Sky Light to get proper outdoors lighting out of the box.
- Set bounce feedback to 0.5 by default to get a better quality result.
- Higher values may cause infinite feedback with bright surfaces.
- Increase the number of frames to converge to improve quality
at the cost of latency. Most scenes are fairly static after all.
- Use 75% Y scale by default as most scenes are not highly vertical.
- Reorder the Y scale enum to go from the lowest Y scale to the highest.
Also rename the "Disabled" setting to "100%" for clarity.
This provides more flexibility between performance and quality
adjustments, especially when using SDFGI for small-scale levels
(which can be useful for procedurally generated scenes).
Values below 0.5 will cause constant flickering in most situations,
and values above 0.99 take a very long time to fully update
(10+ seconds at high framerates).
This property was intended to provide a way to have SSAO or VoxelGI
ambient occlusion with a color other than black. However, it was
dropped during the Vulkan renderer development due to the performance
overhead it caused when the feature wasn't used.
* Functions to convert to/from degrees are all gone. Conversion is done by the editor.
* Use PROPERTY_HINT_ANGLE instead of PROPERTY_HINT_RANGE to edit radian angles in degrees.
* Added possibility to add suffixes to range properties, use "min,max[,step][,suffix:<something>]" example "0,100,1,suffix:m"
* In general, can add suffixes for EditorSpinSlider
Not covered by this PR, will have to be addressed by future ones:
* Ability to switch radians/degrees in the inspector for angle properties (if actually wanted).
* Animations previously made will most likely break, need to add a way to make old ones compatible.
* Only added a "px" suffix to 2D position and a "m" one to 3D position, someone needs to go through the rest of the engine and add all remaining suffixes.
* Likely also need to track down usage of EditorSpinSlider outside properties to add suffixes to it too.
-For inspector refresh, the inspector now detects if a property change by polling a few times per second and then does update the control if so. This process is very cheap.
-For property list refresh, a new signal (property_list_changed) was added to Object. _change_notify() is replaced by notify_property_list_changed()
-Changed all objects using the old method to the signal, or just deleted the calls to _change_notify(<property>) since they are unnecesary now.
-Always use temporal reproject, it just loos way better than any other filter.
-By always using termporal reproject, the shadowmap reduction can be done away with, massively improving performance.
-Disadvantage of temporal reproject is update latency so..
-Made sure a gaussian filter runs in XY after fog, this allows to keep stability and lower latency.
Happy new year to the wonderful Godot community!
2020 has been a tough year for most of us personally, but a good year for
Godot development nonetheless with a huge amount of work done towards Godot
4.0 and great improvements backported to the long-lived 3.2 branch.
We've had close to 400 contributors to engine code this year, authoring near
7,000 commit! (And that's only for the `master` branch and for the engine code,
there's a lot more when counting docs, demos and other first-party repos.)
Here's to a great year 2021 for all Godot users 🎆
Allow gradients and 2d images.
Use shader versions for LUT in tonemap
Co-authored-by: alex-poe <3957610+CptPotato@users.noreply.github.com>
Co-authored-by: QbieShay <cislaghi.ilaria@gmail.com>
Co-authored-by: Clay John <claynjohn@gmail.com>
