Make separation ray shapes work properly in move_and_slide, wihtout the
specific code in CharacterBody like before.
Now most of the logic is handled inside the physics server. The only
thing that's needed is to use ray shapes only for recovery and ignore
them when performing the motion itself (unless we're snapping or slips
on slope is on).
One-way collision is disabled for both rigid bodies and character
bodies.
Kinematic margin is now applied to ray shapes to help getting consistent
results in slopes and flat surfaces.
Convex shapes don't return inverted normals when a segment test starts
inside (raycasting will be made consistent in a separate patch).
Ray shapes also discard contacts when fully contained inside a shape
and when the contact direction is inverted, so the behavior is
consistent with all shape types. Now they always separate only when
intersecting the top of a shape (for downward rays).
Changes:
- Rename few methods/property and group them in the editor when it's possible
- Make MotionResult API consistency with KinematicCollision
- Return a boolean in move_and_slide if there was a collision
- New methods:
- get_floor_angle on CharacterBody to get the floor angle.
- get_angle on KinematicCollision to get the collision angle.
- get_last_slide_collision to quickly get the latest collision of move_and_slide.
Infinite inertia:
Not needed anymore, since it's now possible to set one-directional
collision layers in order for characters to ignore rigid bodies, while
rigid bodies still collide with characters.
Ray shapes:
They were introduced as a work around to allow constant speed on slopes,
which is now possible with the new property in CharacterBody instead.
Same thing that was already done in 2D, applies moving platform motion
by using a call to move_and_collide that excludes the platform itself,
instead of making it part of the body motion.
Helps with handling walls and slopes correctly when the character walks
on the moving platform.
Also made some minor adjustments to the 2D version and documentation.
Co-authored-by: fabriceci <fabricecipolla@gmail.com>
When synchronizing CharacterBody motion with moving the platform using
direct body state, only the linear velocity was taken into account.
This change exposes velocity at local point in direct body state and
uses it in move_and_slide to get the proper velocity that includes
rotations.
The Transform::xform and xform_inv are made safe for Planes when using non-uniform scaling.
Optimization of calling sites to prevent loss of performance from the changes to xform(Plane).
Found via `codespell -q 3 -S ./thirdparty,*.po,./DONORS.md -L ackward,ang,ans,ba,beng,cas,childs,childrens,dof,doubleclick,fave,findn,hist,inout,leapyear,lod,nd,numer,ois,ony,paket,seeked,sinc,switchs,te,uint`
The `Math_INF` and `Math_NAN` defines were just aliases for those
constants, so we might as well use them directly.
Some portions of the code were already using `INFINITY` directly.
Check for each body individually if it collides with the other one or
ignores it.
When a body is being ignored, the other body's mass is considered
infinite when applying impulses to avoid extra overlapping.
Disabled backface collision is only applied on face separation axes,
because applying it also on edges and vertices was causing some contacts
to be wrongly disabled and contact points to be off.
More accurate unsafe motion calculation
* Safe and unsafe motion are calculated by dichotomy with a limited
number of steps. It's good for performance, but on long motions that
either collide near the beginning or near the end, the result can be
very imprecise.
* Now a factor 0.25 or 0.75 is used to converge faster when this case
happens, which allows longer motions to get more accurate collision
detection.
* Makes snap collision more precise, and helps with cases where diagonal collision on the border of a platform can lead to the character being stuck.
Additional improvements to move_and_slide:
* Handle slide canceling in move_and_collide with 0 velocity instead of
not applying it.
* Better handling of snap with custom logic to cancel sliding.
* Remove small jittering when using stop on slope, by canceling the
motion completely when the resulting motion is less than margin instead
of always projecting to the up direction (in both body motion and snap).
Co-authored-by: fabriceci <fabricecipolla@gmail.com>
Make sure the direction of the motion is preserved, unless the depth is
higher than the margin, which means the body needs depenetration in any
direction.
Also changed move_and_slide to avoid sliding on the first motion, in
order to avoid issues with unstable position on ground when jumping.
Co-authored-by: fabriceci <fabricecipolla@gmail.com>
In 3D, disabled shapes are now not added to the broadphase anymore.
Since they are removed right away when disabled, no need to check for
disabled shapes for any query that comes from the broadphase.
Also Fixes raycast queries returning disabled shapes.
In 2D, disabled shapes where already not added to the broadphase.
Remove the same unnecessary checks as in 3D.
Overall harmonized API for disabled shapes in the physics servers and
removed duplicate method.
* RingBuffer had no reason to be in this context
* A single buffer is used that can grow as much as the game needs.
This should make thread loading entirely reliable.
Safe margin property on CharacterBody only, used as argument in
move_and_collide.
Removed kinematic_safe_margin in 3D physics server, not really useful
and now harmonized with 2D.
MODE_DYNAMIC instead of MODE_RIGID
MODE_DYNAMIC_LOCKED instead of MODE_CHARACTER
No more special case for sleeping behavior for MODE_DYNAMIC_LOCKED
(MODE_CHARACTER was forcing the body not to sleep, which is redundant
with can_sleep and wasn't done in Bullet).
PouleyKetchoupp
Jeffrey Cochran
Aaron Franke
LoipesMas
Rémi Verschelde
fabriceci
lawnjelly
luz paz
Hugo Locurcio
Marcel Admiraal
reduz
Rémi Verschelde
Arkadiusz Marcin Kołek