- Based on C++11's `atomic`
- Reworked `SafeRefCount` (based on the rewrite by @hpvb)
- Replaced free atomic functions by the new `SafeNumeric<T>`
- Replaced wrong cases of `volatile bool` by the new `SafeFlag`
- Platform-specific implementations no longer needed
Co-authored-by: Hein-Pieter van Braam-Stewart <hp@tmm.cx>
-Advanced Settings toggle also hides advanced properties when disabled
-Simplified Advanced Bar (errors were just plain redundant)
-Reorganized rendering quality settings.
-Reorganized miscelaneous settings for clean up.
This change makes test_body_motion more reliable when the kinematic body
recovers from being stuck.
- When recovery occurs, the rest information is generated, in order to
make sure collision results from test_move, move_and_collide and
move_and_slide are consistent and return a collision in case of overlap.
- The new calculation for recovery vector makes sure the recovery is
never more than the overlap depth between shapes.
This can help with cases where the kinematic body overlaps with several
shapes.
Recovery is made iteratively, without forcing a full overlap at each
step. This helps with getting proper rest information when recovery
occurs.
- One Way Collision:
When attempting motion, contact direction is checked against motion
before skipping in order to solve cases where kinematic bodies can sink
into one-way collision shapes.
Rest info now sets max contact depth in order to properly handle one-way
collision.
- Low speed motion is now handled in the rest info, by never setting
min_allowed_depth lower than motion length.
Separation is always applied with full margin, otherwise contact is lost
when low speed motion occurs right after higher speed motion.
- Similar changes are applied to 3D in order to make 2D and 3D
consistent.
Cylinder contact points generation is adjusted to make it more stable
when standing on triangle meshes.
Point-Circle:
Switched to simpler plane projection as it's done for Point-Face contact
points. It solves some cases where discrepancies between the two points
caused the cylinder to jump.
Edge-Circle:
Same as before, the case for edge has just been moved from Face-Circle
to a specific method.
Face-Circle:
The previous method was clipping edges against the circle, and then
tried to add contact points when there wasn't enough support and failed
in some cases.
Now using a different algorithm which adds proper contact points around
the circle more consistently.
First, by clipping edges against circle segments using Face-Face
algorithm.
Second, by clipping edges against the circle plane.
Cylinder collision detection uses a mix of SAT and GJKEPA.
GJKEPA is used to find the best separation axis in cases where finding
it analytically is too complex.
Changes in SAT solver:
Added support for generating separation axes for cylinder shape.
Added support for generating contact points with circle feature.
Changes in GJKEPA solver:
Updated from latest Bullet version which includes EPA fixes in some
scenarios.
Setting a lower EPA_ACCURACY to fix accuracy problems with cylinder vs.
cylinder in some cases.
-Rendering server now uses a split RID allocate/initialize internally, this allows generating RIDs immediately but initialization to happen later on the proper thread (as rendering APIs generally requiere to call on the right thread).
-RenderingServerWrapMT is no more, multithreading is done in RenderingServerDefault.
-Some functions like texture or mesh creation, when renderer supports it, can register and return immediately (so no waiting for server API to flush, and saving staging and command buffer memory).
-3D physics server changed to be made multithread friendly.
-Added PhysicsServer3DWrapMT to use 3D physics server from multiple threads.
-Disablet Bullet (too much effort to make multithread friendly, this needs to be fixed eventually).
Inverted the spotlight angle attenuation so a higher value results in
a dimmer light, this makes it more consistent with the distance
attenuation.
Also changed the way spotlighs are computed in SDFGI
and GIPorbes and GPU lightmapper, now it matches the falloff used in the scene rendering
code.
-Always use temporal reproject, it just loos way better than any other filter.
-By always using termporal reproject, the shadowmap reduction can be done away with, massively improving performance.
-Disadvantage of temporal reproject is update latency so..
-Made sure a gaussian filter runs in XY after fog, this allows to keep stability and lower latency.
-Added more finegrained control in RenderingDevice API
-Optimized barriers (use less ones for thee same)
-General optimizations
-Shadows render all together unbarriered
-GI can render together with shadows.
-SDFGI can render together with depth-preoass.
-General fixes
-Added GPU detection
AudioEffectCapture allows access to the microphone and other audio on an audio bus in real-time.
Co-Authored-By: K. S. Ernest (iFire) Lee <ernest.lee@chibifire.com>
Channels that are inactive -or when playback has not started yet- will report -200 dB as their peak value (which is also the lowest value possible during playback).
- Based on C++11's `thread` and `thread_local`
- No more need to allocate-deallocate or check for null
- No pointer anymore, just a member variable
- Platform-specific implementations no longer needed (except for the few cases of non-portable functions)
- Simpler for `NO_THREADS`
- Thread ids are now the same across platforms (main is 1; others follow)
- fixes scale values of 0.0013 (det == 0.00004) not rendering, they should render even at small values, but not at zero like the editor grid plugin supplies zero exactly.
- fixes node_3d_editor_plugin visibility bug when scale is zero
- fix culling with small scaling values - which are still valid to be rendered like 0.00004
note: grid is still not fixed, it has det == 0 issues but this fixes one of them.
-Removed sync to draw, now everything syncs to draw by default.
-Fixed many validation layer errors.
-Added support for VkImageViewUsageCreateInfo to fix validation layer warnings.
-Texture, buffer, raster and compute functions now all allow spcifying which barriers will be used.
-When importing, a vertex-only version of the mesh is created.
-This version is used when rendering shadows, and improves performance by reducing bandwidth
-It's automatic, but can optionally be used by users, in case they want to make special versions of geometry for shadow casting.
