The default portal margin is stored in the RoomManager. Previously this was propagated to Portals when the value was changed, and Portals each stored this default value.
This caused a bug during loading, if the RoomManager was loaded before Portals, the value was never propagated.
This PR makes the default margin a static value stored in the RoomManager, and the Portals now read directly from the static value when required, and do not store locally. This gets around the problem.
Higher values will make indirect lighting brighter.
A value of 1.0 represents physically accurate behavior, but higher values
can be used to make indirect lighting propagate more visibly when using
a low number of bounces.
This can be used to speed up bake times by lowering the number of bounces
then increasing the bounce indirect energy. Unlike BakedLightmapData's
energy property, this property does not affect direct lighting
emitted by light nodes or emissive materials.
Due to an oversight in the autoplace recursive search for static objects, static objects were getting added twice to the portal renderer, which meant they were being rendered twice, lowering performance.
This PR corrects this horrendous error.
Allows users to have the RoomManager as the roomlist.
Fixes a couple of bugs dealing with situations where users attempt to link Portals to Rooms outside the roomlist.
Adds a PortalEditorPlugin allowing you to flip individual portals.
In order to make level building easier, the system can now support STATIC and DYNAMIC objects in the roomlist that are not placed in rooms. The system will automatically place them in the appropriate room.
* Safe and unsafe motion are calculated by dichotomy with a limited
number of steps. It's good for performance, but on long motions that
either collide near the beginning or near the end, the result can be
very imprecise.
* Now a factor 0.25 or 0.75 is used to converge faster when this case
happens, which allows longer motions to get more accurate collision
detection.
* Makes snap collision more precise, and helps with cases where diagonal collision on the border of a platform can lead to the character being stuck.
Additional improvements to move_and_slide:
* Handle slide canceling in move_and_collide with 0 velocity instead of
not applying it.
* Better handling of snap with custom logic to cancel sliding.
* Remove small jittering when using stop on slope, by canceling the
motion completely when the resulting motion is less than margin instead
of always projecting to the up direction (in both body motion and snap).
Co-authored-by: fabriceci <fabricecipolla@gmail.com>
Make sure the direction of the motion is preserved, unless the depth is
higher than the margin, which means the body needs depenetration in any
direction.
Also changed move_and_slide to avoid sliding on the first motion, in
order to avoid issues with unstable position on ground when jumping.
Co-authored-by: fabriceci <fabricecipolla@gmail.com>
- Specular can now be set above 1.0.
- Some properties now allow more precise values.
- The Bake Mode property hint was changed to be more descriptive.
- The maximum shadow bias values were adjusted to follow the property
hints in `master`.
It turned out the new autolinking feature was linking portals AFTER the static meshes had been added to rooms in the PortalRenderer. This meant that large meshes weren't being sprawled across these portals. The fix involves doing the autolinking BEFORE adding the static meshes.
Fixes a bug in the warning for portals being in the wrong direction, they should have only been checkout for outgoing portals. This was resulting in erroneous warnings.
Also the room conversion logs are refined to be more compact and informative.
A warning icon is also added in the gizmo for portals where autolink fails.
Clean: remove duplicate and interior vertices (uses Bullet algorithm)
Simplify: modify the geometry for further simplification (uses VHACD
algorithm)
In the editor, single convex hull now uses the clean option.
Added a new editor entry to create a simplified convex hull, can be
useful for creating convex hull from highly tessellated triangle meshes.
Specific change for 3.x:
Add support for Vector<Vector3> and PoolVector<Vector3> in the convex hull generator.
This backports the improved RayCast debug drawing functionality
from the `master` branch.
`ArrayMesh.clear_surfaces()` was also backported from the `master`
branch and exposed because the new debug drawing code requires it.
Although the visibility enabler worked to turn on and off AnimationPlayer as it enters and exits the view frustum, this was of little use as bones animation and especially software skinning still take place driven by the AnimationTree node.
This PR adds the ability to turn on and off AnimationTree, and AnimationTreePlayer nodes as they enter or exit the view frustum, which achieves the intention of switching off expensive animation processing.
This commits adds a new emitter type for particles material
and 3D CPU particles. The new emitter is called "ring"
and it can emit either in a ring or cylinder fashion.
This adds the following properties for the emitter:
1. ring_emitter_axis: the axis along which the ring/cylinder
will be constructed
2. ring_emitter_radius: outer radius of the ring/cylinder
3. ring_emitter_inner_radius: inner radius of the cylinder.
when set to zero, particles will emit in the full volume.
4. ring_emitter_height: height of the ring/cylinder emitter.
Co-authored-by: Rémi Verschelde <rverschelde@gmail.com>
